Tämä sivu on konekäännetty ja odottaa tarkistusta. Englannin- ja hollanninkieliset versiot ovat määrääviä.

Machinebars.
Machinebars.

Asennus- ja kytkentäohje

Counterweight bar package 2

Konemerkki
Hitachi
Artikkelinumero
110060-23
Dokumentti
PD00094
Revisio
B
Takaisin tuotteeseen

Tekniset piirustukset

  • Tekniset piirustukset 1, Counterweight bar package 2

Asennus, kytkentä ja käyttö

Asennus

Use packaging plastic when fitting clamp brackets to avoid damaging or scratching the bar's surface finish.

Johdotus

Johdotus 1
Connector DT06-08SA 1. Flashlight (+) 2. Flashlight (-) 3. Flashlight night dimming(+) 4. Position light(+) 5. Position light(-) 6. Work light (+) 7. Work light (-) 8. Not connected

Turvallisuus ja käyttörajoitukset

  • The factory products are intended solely as fixtures for lighting and warning systems.
  • Under no circumstances may the product be used for towing or as a lifting device.
  • The product is also not intended for use as a guard rail, handle or step.

Valmistajan ilmoittama tieto

In accordance with VVFS 2003:27 (Swedish regulation), the product's position lighting must not be used while the vehicle is travelling in traffic on public roads. If the product is fitted to a class 1 motorised implement, it must be installed with a switch for the position lights.

Huolto ja puhdistus

Maintenance & cleaning: never spray concentrated jets directly at, or use high pressure (pressure washer) on, lamps and other electronic equipment. All our lamps are IP-rated to withstand water and moisture, but for a longer service life, care is recommended when cleaning. On products with a natural anodised surface, do not use alkaline or acidic cleaning agents; these damage the anodised surface. Only use cleaning agents with a pH between 6 and 8. Paint cleaner may be used on heavily soiled surfaces.

Vilkkukuviot

a. Change the flash pattern by holding the button pressed for about 1 second. b. To reset the flashlights, hold the button pressed for about 5 seconds. The flashlights return to factory mode #0 (Random). NOTE: R65 is the EU-approved pattern and its use is recommended.

9 - Single (all) (R65 - EU Certified)

Näytä kaikki ohjelmoitavat vilkkukuviot
  • 0 - Random (default)
  • 1 - Single (split)
  • 2 - Double (split)
  • 3 - Quad (split)
  • 4 - Quint (split)
  • 5 - Mega (split)
  • 6 - Ultra (split)
  • 7 - Single-Quad (split)
  • 8 - Single H/L (split)
  • 9 - Single (all) (R65 - EU Certified)
  • 10 - Single (all) (SAE)
  • 11 - Double (all)
  • 12 - Quad (all)
  • 13 - Quint (all)
  • 14 - Mega (all)
  • 15 - Ultra (all)
  • 16 - Single-Quad (all)
  • 17 - Single H/L (all)
  • 18 - Steady 2 (California)
  • 19 - Steady 4 (all)

Lähde: tehtaan tuoteseloste PD00094 (rev. B), käännetty ruotsista. Alkuperäinen on arkistoitu. Käännetty toimittajan ruotsinkielisestä dokumentaatiosta.

Machinebars. MachineBars on LMNCOMMERCE:n aputoiminimi, kauppakamari (KvK) 93958927

Ostoskori

Ostoskorisi on tyhjä.

Löydä koneesi valopalkki